Weave bead tie tutorial

By popular demand.

Materials:
1. Scheme of a tie. At the very fact, and no circuit pattern (that is, improvisation) can play a positive role, but to calculate the number of beads in a row, and the proportion of reducing your responsibility. Therefore, it is always better to have ready an empty template scheme. In this master class, I will show a tie netting of large beads, it’s easier and faster. Remember that, depending on the size of beads, the scheme should always be changed! 

2. Machine. His version of I’ve laid out in useful tips, so that the paint will not.

3. Workplace. I think everyone has already formed their habits, so I will not teach academics. I will give only one piece of advice: it is better not to go to the kitchen for a glass of milk, and then your place someone will!

4. Beads. At your discretion. Remark about the number: one set of 50 g I never have enough, but the two always enough, and still remains. Conclusion – 75 grams should be sufficient.

Job Description:
1. Tie fishing line on the tip of a small loop and hook it onto the extreme teeth comb (you can tie a fishing line node). Next, pull on the teeth 20 of warp threads for a tie (on the scheme the maximum number of beads in a row – 19 pcs. Means of threads needed one more). Since the beads have a large, better pull the twine through the 2 prongs. End of fishing line secure with tape.

2. Make a loop at the tip of the working string. I usually wrapped with twine several times around the bottom bracket machine, so after making a tie fasten it with the tip edge of the product. Secure the working yarn knot for 10th warp thread (right center).

3. Position the needle with a thread under the foundation. Strung a bead and place it between the 2 central warp. Supporting bead forefinger, insert the needle into it so that the working thread passed over the basics. Tighten the line.

4. Again miss working thread under the framework and type 2 beads. Attach them to the base.

5. Now the thread under the foundation and type one bead, place it on the other hand dialed segment. Attach the warp threads and pass fishing line through the entire series. Thus done and uniform increase in the number of beads in a row.

6. 4 strung beads and attach them to the base. On the other hand, connect one more bead. Likewise keep weaving angle tie, until you reach the outer warp.

7. Next, make 6 identical series.

8. Sixth row fix for the first warp thread, beating her fishing line and thread the needle through the beads in 6.7.

9. Thread the needle in 2 beads of the previous row in reverse naprvlenii, then in the top row of beads, leaving the outermost bead.

10. Pass the thread under the foundation and continue weaving, picking up 17 beads.On both sides you need to stay free extreme warp. Make 6 rows, then decrease, and so on, following the scheme. When will decrease, whipping a straight line segment.Do not get carried away! Leave a segment basis for at least 6 cm in length, these tips will be needed to secure the tie on the cloth. Recent series go a few times.

Continuation of the master class: fixing warp.
Can hide the beads, you no longer need it. Keep only scissors and a needle.
1. So, we have already prepared a tie, remained hidden thread and make a zipper.

2. Remember the long tip of the working thread, which I was attached to the comb?It was his turn: cut the line, insert a needle and thread to the corner bead.

3. Thread the needle in the second row, then a third, etc. So you once again holds the all series of the angle.

This should be done only if you believe in the hole size beads – if the holes are very small, just go fishing line 3 central beads in each row. In our case, since we use large beads, it is necessary to give a greater density corner. Rows need to go completely.
4. When you pass all the fishing line angle, display it on the right side of the product. Next soedyanyayte series on the right side of the tie touches on 2 beads.

If you still have a long tip of the first working thread (the one that stayed in the top of the article), it can take it to the right edge towards the second strand and tie their knot, put it in beads.
5. Cut the upper side warp.

6. Insert the needle one thread connection and set it in the previous series (until the middle of the series).

7. Likewise please create a thread beads on the opposite side, but go only 4-5 beads, then go down to the bottom row and bring the thread towards the former.

8. Tie the knot yarn, insert both the tip of the needle and set up in the beads. Trim the ends of fishing line.

9. Likewise hide all the upper side warp.

10. Cut one extreme lower warp thread, insert the needle and set up a 2-bead top row.

11. Meshing of 2 beads, yarn output in the 4 th wide range of beads and pass through to the middle of the series.

12. Cut the outermost warp thread from the opposite side of the corner, it also runs in the 4 th wide range, but pass the 5 beads, then go down to the bottom row and bring the thread towards the former.

13. Tie the knot yarn, insert the tips of the needle and hide the knot in a bead. Trim the extra ends.

In principle, all the remaining threads can bind as well, but I’m not looking for easy ways and doing everything wrong.
14. Cut the two extremes thread. Insert the first in a needle and, clinging to 2 beads, display it in a third wide range (rise of 3 series).

15. The second thread lift for 3 series, and bring to the first thread.

16. Tie the knot yarn and hide in the beads (do not go over the center line). Trim the ends.

17. Cut 2 more extreme fibers and secure them in the same way, raising a 3 series.

18. On the opposite side of the corner as secure four outer thread.

19. Other threads are going to fix a little differently. Cut the two extremes thread.First lift of 4 series.

20. The second also raise a number of 4, and bring next to the first.

21. Tie the knot yarn and hide in the 3 beads, trim the ends.

22. Likewise hide all the warp threads. The machine can be postponed, it is no longer needed.

Enough for today, but then my mother refused to show sewing fabric. Wait for tomorrow night + tying knot!

A simple tie.

Several times asking how I am doing a node in a tie, so she decided to try to explain
strip lashes  under this scheme to the desired height node dlinshe something to think about the length of the tie

folded ribbon so the knot was a double

the edges ….

Then pass through a thread in the Territory, the site,

recruit 1 or 2 beads although you can without them,

introduce a thread in the parallel bead, an extreme bead with a hearse hand,

delaying

Anchoring the line, ready! seamy side

face


and white

Necktie (Austria:)) of cultured pearls

Tie “Austrian”.
That is, decided to hang out in the master class (since I’m sure the picture all clear, she drew on the memory, long tie given ordered it). The story is: bring me “break” tie torn, once bought in Austria .. The scheme I liked, remembered for yourself. Tie repaired, although nearly all had twisting again. Then saw a similar tie in an Italian magazine of beads, but there site is lagging harder. I then put in the schemes, if somebody can translate the description of the schemes from the Italian  )

My first master class, do not judge strictly.
Slightly changed the description, because proplela tie and found errors .. 

For the product will need:
1) Cultured pearls, about 420 beads 4 mm in diameter,
2) line (with diam.zatrudnyayus .. guess not .. 0,25 mm thick, but not monofilament)
4) needle for beads
5) carbine + ring to buckles + 2 Culotta

Weaving start with the lowest cross (red beads), then proceed to cross on number 2, then 3 and so on, gradually increasing the number of beads up to 6 (web width), and it turns out that each cross pass at least twice. Therefore, we obtain a strong tie and sprawls on a slippery fishing line. The whole difficulty in the fact that the needle and line slipped many times as necessary in the bead.

Once the fabric has reached 6 beads wide,
cease to add beads on the sides and whip up the canvas: row after row of horizontal rows, respectively, the scheme and the desired length of a tie (in my case it was 16 rows of 6 beads up .. alternating, of course, rows 5 and 6 of the beads and tie .. is a bit longish. So in this case it is necessary to make an amendment to the desired length ..)
That is, suppose we got to the point where the tie will host.

Next, add the beads on the web width, up to 7 crosses:

Scourge canvas high seven crosses:

Then add both sides of the chain for fasteners for the length (around the neck) 40 cm I got on each side of 32 beads of 4 mm diameter. Further touches shotgun and a ring for the clasp (you can add an extension chain if necessary), we behold such a thing:

(Marked with red beads, which cling to the chain of beads for fasteners).

Next begin to weave a proper node itself .. For this painting would have to wrap right and left of the center, and connect the beads, marked here in this picture:

Step 1. 1 conn. The green beads, 2 “blue”:

Twine tightly contractible:

To make it easier to pass the lower three beads on a circle (since it is precisely here, at the bottom of the tie will be the greatest tensile strength), add one more (marked in black), obtained by the cross, it can take several times to the fortress:

Step 2. 4 “orange” beads:

Step 3. 6 “bright pink” to connect the edges of the beads:

Step 4. 8 “yellow” conn. beads:

Step 5. 10 “dark green beads, the last series. They cling to the same beads as the “yellow” series, and for the beads, marked in red (of which are side chains clasps).

The result is now a tie (wrong side):

He had a somewhat similar to the “tube”. But when wearing a tie, the side chain of zip stretch knot in hand, the result is fairly flat and elegant uzelochek 

Here is the finished tie inside out:

And this kind of finished the tie with a person:

source: www.biser.info