Featured Post

New Post

Popular Post

Recycling ideas: jewelry making

Green crafts, Jewelry making, Recycle  |  September 8th 2011  |  0 Comment

Drop-Dead Denim: Mi-Shell’s Pendant


You don’t mind if I just jump in and get the crafts rolling do you? I mean, let’s be honest, that is why we’re here. So let us delay no longer. Let us DO it man.
Tutorial: Mi-Shell’s Denim Pendant
You will need:
  • Some jean scraps in a few different tones if you like
  • Glue (I used fabric glue but PVA glue works fine)
  • A dribble of acrylic paint and a small paint brush
  • Fabric stiffener (I used um… “Stiffy” by Plaid. Yes. That is its name.) and a paint brush
  • A pair of scissors
  • A circle template (small round thing about 2″ (5 cm) in diameter)
  • Pen
  • Needle and thread
  • Jump ring
  • Large sewing needle
  • Cord or crochet cotton and small crochet hook
1. Cut 5 strips measuring 1/4″(6 mm) wide and about 6″(15 cm) long. One at a time apply glue along the length of a strip.
2. Coil up the strip.
3. This makes a denim bead. Repeat steps 1-3 for the remaining 4 strips.
4. Apply paint to one flat face of 2 of the beads (or however many you’d like to paint).

5. Using your circle template, draw out 5 circles onto your denim scraps and cut them out.
6. Fold circles in half. Press.
7. Unfold a circle. Apply glue to the inside top and bottom of the circle.
8. Take a denim bead and sandwich it between the top and bottom of the circle as in #8. Hold for a few seconds. Repeat steps 7 and 8 with all circles.
9. Take all folded and beaded circles and hold them with their spines lined up as in #9.
10. Take a threaded needle and starting at one end, stitch your bundle together along the spine using a running stitch.
11. Stitch along the whole spine until you get to the other end. Tie off with a knot. Hide your thread end by sinking it into the spine.
11-1/2. This step is hard to explain. But I’ve got to try! With the help of small needle nose pliers to pull the needle and thread though the beads, start at one of the outer circles and stitch with needle and thread, through the diameter of each bead to the other side of the pendant. This will ensure that the beads stay in place within the circle sandwiches.
12. Break out the fabric stiffener and a brush. Pour some stiffener onto a plate or plastic cover.
13. Brush the stiffener generously onto and into the pendant. If necessary use a smaller brush to get the stiffener into all those nooks and crannies. Let the stiffener dry (sort of). I threw my pendant in the microwave for 30 second increments to heat it up and promote drying.
14. When the pendant is dry (sort of), shape it between your fingers to the desired shape. I was going for a shell-like shape. When I was pleased with the shape, I let the pendant dry completely. I used a LOT of stiffener so my pendant is quite hard.
15. Make a hole a one end of your pendant to accomodate a jump ring. I used a large needle to make my hole.
16. Open up the jump ring. Insert it into your hole. Close up the jump ring!
17. I crocheted a simple chain for my pendant using crochet cotton but you could use any nice piece of cord. Put the cord through the jump ring. Make a rudimentary clasp by taking one end of the cord and tying it to the other end of the cord (a few inches down from the end) with a simple knot.
18. Repeat that last sentence with the other end of the cord to complete the clasp.
19. This makes a nifty adjustable clasp. To adjust the length of your cord, simply slide the knots over the cord either closer or further from each other.

Could it possibly be done? Why yes, I think you can call that a pendant! Yippee cayay!

Take a look…
Here’s the back…

It reminds one of sea critters, doesn’t it?
Or brains maybe?…

Have you ever made sea creatures or brains out of denim?
Source: @michelemademe.blogspot.com