Garden sculptures of foam

Some of the “Japanese lanterns Tachi-gata” I invented myself. “Sm.Fonarik below ..

Frog of foam!

If someone is interested in how it was done, lo, the spread.
Will need: 1 bottle foam, 1 old saucepan with a diameter 20-23cm, 1banka (Metal) from a tomato paste-volume 1L, 2businy (eye), oil paint (white) and color.
1. Poured, and poured two containers with foam. Allow to dry.
2. Strengthens the body and head with wire, pins, rods …, fixes immediately foam.
3. Insert the wire in the location of the alleged legs. Pouring cautiously, gradually at intervals to dry. Eyes inserted into the last turn, after painting animal!

Sculptures for the garden of the foam. “FOX”

For the manufacture of figurines will need:
Polyurethane foam
Gun for polyurethane foam.
Cleaner for foam. (Need to wash gun for cleaning hands)
Gloves made of cotton, not one pair.
For the manufacture of the figures I used are usually empty bottles of kefir.
1 put the sand into the bottle (for gravity to a figure not crabs). Propenyl fully the bottle. Attention! Propenivat must gradually, layer by layer, to give time to dry between coats. Dry foam about 10-15minutes.

2, 3 To produce the paws, tail, I used a tube with a threaded wire. Stick a tail (it keeps the entire figure), legs (pipes), specify the desired curve, propenyl the joints. Neck: Insert tube from under the toilet paper, propenyl. Dry.


4 propenyl paws, tail.
5 For the manufacture of the head, you can insert something round and propenyl. Ears: Cut out of cardboard, soft plastic.Embed tabs in place, propenyl, dry .. Mustache: Cut thick twine, paint over with black paint from the bottle insert. Eyes – it’s rubber balls painted with the same paint.
sculptures made of foam paint over oil paint, the top can be painted (if not a figure painted with white paint as paint gives yellowness).

Statuette of the foam in the garden! “Internet Map”

Basis for kolobok I took Christmas toys, plastic ball can be that something round. Propenyl ball with postepennnoy drying layer by layer.

Handles are made of tubing with threaded wire. Set binding, propenyl. Solitaire – this is also the foam. “Ears” on the headscarf: Cut out the cardboard leaves, embed, propenyl. With a sharp knife to cut eyes, mouth.


Inside the legs, the usual wooden wedges, propenyl specifying the desired shape.

Paint over oil paint, can be coated with varnish.

Master Class tachi-gata “Japanese garden lantern.

1Trubu set on a flat surface, propene on the bottom of the pipe to fix it. Dry. To secure the cup to the tube, drilled 3 holes in the pipe (top) and 3 holes in the cup (bottom). Fasten with a wire.

Pour the foam from the outside, according to a pre-thought-out pattern. ! Pour foam layers with drying between coats.
2, 3,3 a



4 In the middle of the cup to drill a hole (for screw). Prepare bar, make 2 holes in it, then to secure the cover screws. Fasten the bar to the bottom of the cup. 4

5 propenyl inside the cup.

6 Cut from a sheet of particleboard or plywood – the first square, mark the center, drilled for screws, propenyl, dry. Propenyl, and the reverse side (cover)

7 How can better shed foam (you can then trim)

8 Pin (large self-tapping) the center caps with the bar.

9 out of a piece of chipboard or plywood Saw a second square with a smaller size, the edges of screws to fix four wedges, which will be mounted rack. In the middle of the square drill a hole for the solar lantern.

Propenyl reverse side of the square, then dry.

10 Lock screws rack. Combine this square with the first square and fasten screws.

11 propenyl top of the second square. Expose the edges of the square of the small studs to pull the thread around and tie.According to this thread “pour” foam giving a flat strip – an edge.

12 between the posts put 4 small strips, secure, pre-make them in two – three small holes for studs. Fasten the rail studs, just sticking them into the foam. Propene.

13 Insert solar lantern. (Lighting)

14 dig up a hole for the output wiring out.

15 Fasten the solar panel on the side.
!!!!!!! Item 13, 14, 15 can be done later, before you put the main dome. As inconvenient to make a drawing.

Dome. 1 From the piece of chipboard or plywood, cut a square is bigger than the first square. ! Make a template for the posts.Grab a sheet of paper neatly superimpose it on top of the rack, note the exact middle of the marker stands. Shifts this piece on the square – a dome perekalyvaem our point – note. Drill holes in the dome and stands (middle) to join them later with screws.In the dome insert screws! Screws not to remove, so as not to lose the hole!

2 According to the center of the exhibit tank-type pot, propenyl it carefully without touching the top of pot-capacity.

3 At the top of the pot supply capacity (small pot), propenyl all, leaving the top of the pot.

4 Insert one (flower) pot, propenivaem it only outside.

5, 6, cut from plastic or (soft board) strips, anchoring their nails as shown in the photo.


7 Propenivaem inside the dome to the strips. Draw the desired pattern. In the hole you can insert any tip – the peak!

8 Finish with symbols dome, combine with racks, anchoring screws.

9 paint over a product! I took a risk and painted with oil paint, I think it should not peel.

10 Mounted hack it so. Lumps trying to drive down pipe somewhere around 40 cm, paint over it with bitumen. Finished crafts dig in the ground by placing it in the central part of the garden. You can just make crafts high, without a hammering chocks on the bottom of the pipe, but I did not let the ceiling in the basement. IMPORTANT! Attach to the form of our crafts! Grab a gun with foam and carefully, carefully close up all the all small and not very – holes. Should look at different angles to fill them carefully. The only way to avoid untidy, “clumsy” appearance, and make crafts clear embossed.
! Apply the relief on the crafts have a preliminary geometrical calculations ie paint or marker to note the desired pattern.Perhaps all!

Iguana

Do not know if you are interested as made “Iguana”. It took her a little more than two Balonov foam. Painted with oil paint, lacquer on top for yachts.








Carcass “Iguana”. Torso – is kefir bottle with sand, closed the lid, propenenaya top .. Head – a glass of sour cream, coca cola …- propeneny both outside and inside. Next, connect the two parts of the body and head. Making a hole in the ground connector, insert the tube with the wire is secured to foam entirely. Propenivaetsya body in long form, something resembling iguanku.Feet: – cut 4 pieces of pipe – it can be a normal hose, it smuggles the wire (for the desired bend). Dig up holes in the ground mounting pads, insert foot, to fix the foam, to give time to dry. Propenyl feet, build a fully foam and the top (back) and bottom (belly). TAIL: – Cut a piece of tubing (you can take the hose again) to miss inside the wire, bend the tail set. Dig up a hole for the tail, put a “tail”, propenyl completely. CLAWS – Cut cocktail rolls, skip to the bottom of the wire segments. Vstvlyaem in paw claws-blank, propenyl. ROTH: Draw a marker for the location of the mouth. Carefully make a cut with a sharp knife, shaping the “mouth”. EYES – dig up holes for the eyes. Insert the eye, fix the foam. ! To hack looked carefully, not clumsy … the form, you must propenyl all the small holes-holes. Painted with oil paint, varnish.

The surface of the Iguana (skin), it strips and balls slightly elongated. If this strip, then squeezing the foam and moving ie pull.The same extended the “ball” – squeezing the foam, we adhere to a few, give the volume and drag. Practice on cardboard, you could do it, it really is not difficult!

Today, painted a wooden shed and made a cat. Cat cut out of plywood, propenyl top, giving it a shaggy.


Step by step photos of some of the craft foam can be found on pages 5-7.
The foam is applied postepennno those filled coat, a little dried out again i.t.d layer to the desired volume figures. Well here’s another odd job “Cat”, though primitive, but still show.
Draw on a piece of cardboard figure, place it on the plywood and cut a jigsaw (you can just draw on fanerke). Pour a layer of foam to dry.
(This picture does not increase, but I still understand everything and be seen …)

Next, pour the second layer, (tretim..)

Make a foam “wool” Drain crafts, how to paint over oil paint can be covered with lacquer or varnish for yachts for outdoor use.

source: img0.liveinternet.ru