Featured Post

New Post

Popular Post

Craft lessons: transfer techniques for embroidery

Embroidery  |  September 7th 2011  |  0 Comment
Transfer Patterns

 


When cutting out your pattern, be sure to leave enough room around the image, so you can hold it securely during the ironing process.
When you have the image cut out and you know where you want to place the image, PRE-HEAT YOUR FABRIC FIRST (make sure you’re steam setting is OFF too! -Jenny). This is a very important step and should not be skipped. This is almost always the first question I ask when troubleshooting, “Why didn’t my pattern transfer?”

After pre-heating your fabric, put the transfer face down on the fabric, and iron. Hold on to your image securely, and press your iron on top of your image for about 10 seconds. Try not to move your iron, because you just might “ghost” or smudge the image, and that’s not fun. The image will be permanent.
Be sure plenty of fabric still surrounds your image, so you can allow for hooping.
An embroidery hoop has 2 pieces. The adjustable ring will be the top piece.


Once your fabric is hooped and you’ve got the fabric tight like a drum head, you’re ready to start embroidering! That’s all there is to transferring an iron-on pattern. By far, this is the easiest way to go.
But perhaps you’ve found an embroidery pattern on Etsy, or you’ve found another image online, or you want to embroider one of your own drawings. That’s what we’ll talk about now.
Pictured above are various transfer tools: Transfer pencil,
Wooden Stylus, Metal Stylus and Transfer Pen.
-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-
Method 1: Carbon Transfer Paper
Materials:
*Free Embroidery Pattern from Jenny Hart
* Carbon transfer paper
* Tracing stylus
* Ballpoint pen or pencil
*tape


If your design has lots of fine lines and details or if it’s a large pattern, I would use the carbon
transfer paper method.
-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-
Method 2: Iron-on Transfer Pen

Materials:
Pattern of your choice and
Iron-on transfer pen
When you first get your Sulky transfer pen, the tip will be white. Each time you use the pen, you’ll need to press the tip down about three times to get the ink to flow in to the tip. Don’t over do it though, because sometimes the ink tends to pool up.
That’s why I recommend testing your transfer pen on a different piece of paper before you start tracing your design.

Remember to pre-heat your fabric first, and hold on to your design, to prevent smudging. This method is also permanent.
You can see the Sulky transfer pen leaves chunkier lines, so you’ll need to learn not to use a heavy hand when tracing your design. I use the transfer pen method A LOT. I really love this product, and highly recommend adding it to your embroidery toolbox.
-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-
Method 3: Transfer Pencil
Materials:
Pattern of your choice and transfer pencil (usually found at any craft store.)


I have to be honest, this is my least favorite transfer method. (I second that! -Jenny) The lines are just too faint for me, and sometimes they don’t transfer at all after ironing. But I will use it if I’m in a pinch.
-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-

The above photo shows all three of the transfer methods I just discussed. You’ll have to play around and decide what works best for you!

Source: @sublimestitching.com