Featured Post

New Post

Popular Post

Craft flower: Felt Flower Pillow tutorial

Felt, Making flower, Sewing  |  September 16th 2011  |  1 Comment

Felt Flower Pillow

Have any old boring throw pillows laying around?

If you answered “yes” then you may want to take a look at this tutorial.

Handmade felt flowers are a perfect way to add a little character to your old throw pillows. Not only are they fun and charming to look at, they cost next to nothing (felt is only about 25cents per sheet)!

This tutorial will show you how to make a felt flower pin to dress up your old shabby pillows. The pin is super convenient because it can be easily removed and replaced.
Click below for a step-by-step tutorial!

Felt Flower Pin

Materials
2-3 sheets of felt, color is optional (I used cream and stone)
2-4 bar pins
fabric scissors
hot glue gun
small needle
tread to match felt color
push pins
paper
pen

Note: The tutorial for this project will show instructions for the largest felt flower (seen on the upper left hand corner of the pillow) If you want to vary the sizes of your flowers simply adjust the measurements I give to fit your preference. The largest flower begins using 2-3/4″ wide squares and the smallest flower (at very bottom of pin) begins using 1-1/2″ wide squares.

Step 1. Cut out 5 squares of felt 2-3/4″ wide. Then cut each square into a circle by rounding off each corner of your square. Don’t worry if the circles aren’t completely perfect you wont be able to tell once your flower is finished.

Step 2. Take one of your circles and fold it in half, like a taco. Take your threaded needle through the felt circle (about 1/4″ away from the end of your taco).
Step 3.Take your needle back through the same spot, this will create a loop in the thread. Take your needle through the loop, then pull thread tight. Repeat this step about 3 times, looping your needle through the same spot.
Step 4. Cut the ends of your thread and tie off.
Step 5. Repeat these steps with all 5 of your circles.
You will end up with 5 puckered flower petals.
Step 6. Cut off the ends of each petal, this will allow the petals to lay closer together once your flower is assembled.
Step 7. Cut another circle of felt, about 2″ in diameter. Hot glue the ends of each flower petal and place on felt circle in a star-like shape.
You can tuck the petals underneath each other to create a look like this…
Step 8. For the center pieces of the flower, cut out 3 more felt squares about 1-1/2″ wide. Then cut the squares into small circles.
Step 9. Starting from the outside of your circles, cut each one into a spiral (about 1/8″ thick).
Step 10. Take the outer end of the spiral and roll the felt into a cinnamon roll shape. Then, place a dab of hot glue on the back and glue down the rounded piece at the end of your spiral. Repeat these steps for all 3 of your small circles.
Step 11. Hot glue the 3 spiral pieces to the center of your flower.
Step 12. Once you have made all of your flowers, (you can make however many you want!) place them on your pillow however you please. Then take a snapshot of it, so you won’t forget how you want them to lay).
Step 12. This may be a little tricky but you need to sort of eyeball the shape of your flowers, and draw the out line on a sheet of paper. (you will use this as a backing for your flower pin).
Step 13.  Cut out your shape and pin it to a piece of felt.
Then cut the felt using your shape as a pattern.
Step 14. Refer to the picture you previously took and lay your flowers on the felt backing piece. Then pick 1 flower up at a time, and glue if down. You can play with the flower petals as you glue, and overlap them in wherever way looks best. (After all the flowers are glued down you can cut away any pieces of the backing that are showing through).
Step 15. Take 3 bar pins (or however many you need)
and hot glue them to the corners of your felt backing.
Now pin to your pillow, and your done!
Source: strawberry-chic.blogspot.com